[vhdl-200x] VHDL PAR P1076 (VHDL-200X / Accellera 3.0) Invitation to ballot

Hi,
The VHDL PAR P1076 (VHDL-200X / Accellera 3.0) is
ready for ballot pool formation.  Please join the
ballot group as described below.

If you intend to ballot on this revision of 1076,
please join the ballot group before 5-July-2007.

If you did not get the below notice from IEEE, make
sure to login to MyProject and express interest in
the following working under "MyProject > Manage Activity Profile":
   IEEE Computer Society  C
     Design Automation  C/DA   VICTOR BERMAN
       VHDL Analysis and Standardization Group C/DA/P1076 JIM W LEWIS

Best Regards,
Jim Lewis
IEEE P1076/VASG Chair



***** SPONSOR BALLOT INVITATION *****
You have indicated an interest in balloting IEEE Standards documents.

IMPORTANT! To participate, you must have access to myProject through an IEEE Web Account.

If you would like to participate in IEEE Standards Sponsor Ballot
P1076
Title: Standard VHDL Language Reference Manual
you must enroll as a member of the ballot group by 5-Jul-2007, 11:59 p.m. Eastern Time.

***** IEEE STANDARD DOCUMENT INFORMATION *****
The IEEE Computer Society Society/IEEE Standard VHDL Language Reference Manual invites you to participate in the 
Revision Sponsor Ballot for:
P1076
Title: Standard VHDL Language Reference Manual
Scope: This project will revise and enhance the VHDL LRM by including a standard C language interface specification; 
specifications from previously separate, but related standards 1164, 1076.2 and 1076.3; and general language 
enhancements in the areas of design and verification of electronic systems.
Purpose: The VHDL language was defined for use in the design and documentation of electronics systems. It is being 
revised to incorporate capabilities that will improve the language's usefulness for its intended purpose as well as 
extend it to address design verification methodologies that have developed in industry. These new design and 
verification capabilities are required to ensure VHDL remains relevant and valuable for use in electronic systems design 
and verification. Incorporation of previously separate, but related standards, will simplify the maintenance of the 
specifications.


***** ENROLLMENT INSTRUCTIONS *****

Go directly to:

https://development.standards.ieee.org/my-site/open-ballot-invitations

Or, follow this process:

1. Log onto myProject; click the link for myBallot.
2. Click the link for myBallot Control Panel (if applicable); click the link for "Show/Join Open Ballot Invitations": 
https://development.standards.ieee.org/my-site/open-ballot-invitations
3.  Scroll down until you find the open ballot group of interest to you; then scroll over to the right margin and 
click ?join? under the ?Actions? column.
4.  Select a classification category and click ?OK? at the bottom of the screen.  You will receive an on-screen 
confirmation that you successfully joined the group.

If you are not an IEEE SA Member, you can either enroll in a single ballot by paying a per-ballot fee or you can join 
the IEEE SA by choosing an option link below.  Joining the IEEE SA entitles you to participate in as many sponsor 
ballots as you like for the year.

OPTION 1 - I am already an IEEE Member and I want to add Standards Association Membership. Go to: 
https://myieeemembership.ieee.org/renewal/RenewalLogin
OPTION 2 - I am not an IEEE Member but would like to enroll in both IEEE and IEEE Standards Association. Go to: 
https://webapps2.ieee.org/member/Member
OPTION 3 - I am not interested in becoming an IEEE Member, however I would like to enroll as a Standards Association 
Member only. Go to: http://standards.ieee.org/sa-mem/join.html

============================================
OBLIGATIONS AND RESPONSIBILITIES OF BALLOTERS
============================================
Balloting group members are selected to vote on the acceptability of a new or revised standard, or on the reaffirmation 
of a published standard submitted by the Sponsor; based on interest in and commitment to reviewing and voting on a 
specific existing or proposed standard.

Once the document is ready to be balloted, you will receive notification via email.  You will typically have 30 days to 
review the document and return the ballot with your vote.  By agreeing to participate in this ballot you have an 
*obligation* to respond.  Failure to return a completed ballot may disqualify you from participating in future ballots.




-- 
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Jim Lewis
Director of Training             mailto:Jim@SynthWorks.com
SynthWorks Design Inc.           http://www.SynthWorks.com
1-503-590-4787

Expert VHDL Training for Hardware Design and Verification
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.